The Gauge Number Written on the Sheet

A gauge identity is on the sheet. The gauge on the bench has a tag. You run a finger along the smudged handwritten number next to the stamped part number at the top left, matching the etched serial on the gauge’s plastic body to confirm you grabbed the correct tool for this run of 316L stainless steel flanges. You don’t move the sheet from its slot at the edge of the bench until you confirm both numbers align, no crossed digits or misread scrawls from the production lead who dropped off the job this morning.

Gauge Serial Alignment With This Sheet’s Printed ID

You hold the gauge tag flat next to the printed 7-digit serial at the top of the sheet to eliminate parallax error as you compare each digit. Even a single mismatched digit means you’re using a gauge calibrated for a different tolerance range, which can produce false pass or fail readings that derail the entire 120-part run. You initial the small box next to the printed serial once you confirm a perfect match, no exceptions, even if you’ve used this same gauge for three previous runs of the same flange design. You only set the gauge in its designated foam rest on the bench once that initial is dry, so you don’t smudge the mark or knock the gauge out of alignment before you start testing.

The Gauge Number Written on the Sheet
The bin is shut.

Number Cross-Reference For 316L Flange Wall Thickness Checks

You use the printed cross-reference table at the top right of the sheet to map each sequenced part number to its required thickness reading, following these steps for every part in the run:

  1. Locate the 4-digit part sequence number stamped on the outer lip of the flange, and find that same number in the leftmost column of the sheet’s cross-reference list
  2. Note the minimum and maximum allowed thickness values listed next to the sequence number, adjusting for the 0.001 inch offset printed next to the gauge serial to account for its recent calibration
  3. Place the gauge’s flat contact face squarely against the inner wall of the flange, applying only enough pressure to seat the probe fully without flexing the thin flange material
  4. Write the exact reading from the gauge’s digital display in the blank box next to the corresponding sequence number on the sheet, rounding to four decimal places exactly as listed in the cross-reference
  5. Mark the small pass/fail checkbox next to the reading based on whether the value falls within the listed min/max range, circling the reading in blue ink if it falls within 0.0005 inches of either threshold for extra review by the quality team.

Illustrative example: For sequence number 4279, the allowed min thickness is 0.1245 inches and max is 0.1265 inches, so a reading of 0.1247 is a pass, while a reading of 0.1244 is a fail, no partial credit for near-miss values. You don’t adjust any readings to push a part into the passing range, even if you only have three failed parts allowed for the entire run before the lot is flagged for rework.

Sheet Annotation Spots For Pass/Fail Readings Per Sequenced Part

You only write readings and pass/fail marks in the pre-printed boxes allocated for each sequence number, no scribbling in the margins or crossing out entries to rewrite them. If you make a mistake when writing a reading, you draw a single thin line through the incorrect entry, write the correct value directly above it, and add your initials next to the correction so the quality team knows who made the adjustment. You never use white-out or opaque tape to cover an incorrect entry, as that counts as an unauthorized alteration of the job record that can void all readings for the entire run. If you need to add notes about unusual readings, you use the dedicated notes section at the bottom right of the sheet, labeling each note with the corresponding sequence number so there’s no confusion about which part the note references. If you run out of space in the dedicated notes section, you request a supplementary annotation slip from the Traveler Desk, attaching it to the back of the sheet with a single staple in the top left corner so it doesn’t fall off during transport to quality.

Written Tolerance Bands Tied To This Gauge’s Stated Accuracy Rating

The written tolerance bands on the sheet are calibrated specifically for this gauge’s ±0.0003 inch accuracy rating, so you don’t substitute a different gauge even if it looks identical or has a more precise accuracy rating. A gauge with higher accuracy can produce readings that fall outside the pre-determined bands for this job, leading to unnecessary failed parts that waste material and extend production timelines. You double-check the tolerance bands against the gauge’s calibration certificate listing (printed on the back of the sheet) before you take your first reading, confirming that the listed accuracy rating matches the value etched on the gauge’s body. If you notice a mismatch, you flag the sheet for the production lead immediately, don’t take any readings until the discrepancy is resolved, even if the run is already behind schedule. You also check that the calibration date on the certificate is within the 90-day valid window, as an expired calibration invalidates all readings taken with the gauge, no matter how consistent they appear.

Logged Gauge Calibration Expiry Date Printed On This Sheet

The logged calibration expiry date for this gauge is printed directly below the serial number at the top of the sheet, so you don’t have to pull separate calibration records to confirm the gauge is valid for use. You circle the expiry date with a black pen once you confirm it falls after the scheduled completion date for this run, so the next person using the sheet can see at a glance that the gauge was valid when readings started. If the expiry date falls during the run, you stop taking readings immediately when you reach that date, notify the production lead, and wait for a newly calibrated gauge with a matching serial before you resume work. You never take readings with a gauge that’s past its calibration date, even if you only have two parts left to test, as those readings will be rejected by the quality team during their final review. You also note the date and time you stopped work if you hit a calibration expiry mid-run, writing that note in the dedicated notes section at the bottom of the sheet with your initials for traceability.

Next Shift Gauge Confirmation Step When You Pull This Sheet

When you pick up this sheet again, either at the start of your next shift or after you complete a different job in between, you repeat the full serial alignment check for the gauge before you resume taking readings. You don’t assume the gauge is still the correct one just because you left it on the bench next to the sheet, as other operators may have borrowed it for a different run and returned the wrong gauge by mistake. You initial the second small box next to the printed serial each time you resume work on this run, so the quality team can see every point where the gauge was verified for use. If you’re picking up the sheet to continue a run started by another operator, you also check their initials next to the serial number and confirm that they signed off on the calibration expiry date before you start taking readings, so you don’t rely on unvetted checks from someone else. You also zero the gauge against the 0.125 inch calibration block included with the tool each time you resume work, recording that zero check value in the small box at the top of the cross-reference list to confirm the gauge is reading correctly before you test any parts. Any deviation of more than 0.0002 inches from the calibration block value means you need to re-zero the gauge, and if it won’t hold a zero, you flag it for the calibration team and wait for a replacement before you continue.

About · Contact · Privacy · Disclaimer · Advertising · Terms