Quantity Ordered vs Quantity in the Bin

The traveler states a quantity. The bin in front of you has a count of its own. You set your digital caliper down on the workbench edge, wiping machining coolant off your work glove before you pick up the sheet. No one has marked any discrepancies on the line for this part number yet, so you run through the count yourself before touching any stock. The part you’re pulling is 4130 chromoly rod ends, pre-cut to 2 inch lengths for off-road suspension assemblies.

How this sheet flags mismatched stock counts

This sheet pulls the required production quantity directly from the active work order tied to the current run, and pre-fills the last logged bin count from the most recent cycle check completed 72 hours prior. Any gap between the two numbers larger than 3 units triggers the manual count step you’re completing right now, to ensure you don’t run out of parts mid-run or overpull stock that’s reserved for another job. Once you sign off on the count, you scan the sheet’s QR code to send a copy to Traveler Desk for inventory tracking. You don’t adjust any pre-filled numbers until you’ve done two full physical counts of the bin, to avoid entering errors that throw off downstream kitting and restock schedules for the rest of the month. Illustrative example: A discrepancy of 7 units for part number CR-219 triggers an immediate restock request from the raw materials cage, even if you can pull enough from a secondary bin to cover the current order.

Quantity Ordered vs Quantity in the Bin
The packet stays closed on the bench.

Steps you take before you mark any count adjustment

Before you write any number on the sheet, you first sort through all parts in the bin to separate any damaged, mis-cut, or incorrectly sized pieces that were left by the previous shift. You set those pieces aside in the scrap bin next to your work station, and count only the parts that meet print specifications for the current run. Next, you cross-check the part number printed on the bin label against the part number listed on the sheet to make sure you’re pulling from the correct bin, even if the bins are in their usual assigned slots. You then count the parts a second time to confirm your first count is accurate, before you enter any number in the physical count field. If you notice any parts in the bin that don’t match the listed part number, you set those aside in the mismatched parts bin by the rack and note that in the margin later, so the inventory team can rehome them to the correct storage spot.

Count verification fields this sheet uses for part tracking

Every field on this sheet is designed to reduce manual entry error and give full context for any count discrepancy, so you don’t have to follow up with multiple team members to resolve gaps later. The table below breaks down each required field, what you enter in it, and common mistakes to avoid as you fill it out:

Field Label What you enter Common mistake to avoid
Bin ID Alphanumeric code printed on the left side of the bin’s front label, matching the code pre-filled on the sheet Typing the adjacent bin’s ID by mistake when bins are stacked close together on the rack
Current Physical Count Exact number of spec-compliant parts you count after sorting out damaged or mis-cut pieces Rounding up to match the ordered quantity to skip additional manual checks for small gaps
Required Order Quantity Number pulled directly from the top line of the work order tied to this production run Copying the quantity from a different work order for the same part family that’s scheduled for next week
Discrepancy Code 2-letter code matching the reason for any gap between counts (OS for overstock, US for understock, DM for damaged parts) Leaving this field blank even if the counts match by random chance, to confirm you completed the full check

If you have a gap that’s not covered by the standard discrepancy codes, you can add a custom note in the margins later, but you still fill in the closest matching code to make inventory sorting faster for the admin team. You don’t use abbreviations that only you understand, because the inventory team processes hundreds of these sheets a week and won’t have time to follow up for clarification.

Notes you add to explain any deviation between the two numbers

You use the 2-inch blank margin at the bottom of the sheet to write short, specific notes that don’t fit in the standard fields. For example, if 4 parts were damaged during the last machining run and left in the bin by the previous shift, you note that next to the DM discrepancy code so the inventory team knows to pull those parts for scrap reprocessing. You don’t use vague phrases like “count is off” because that forces the next shift to redo your entire count to figure out what caused the gap. If you pull extra parts from a secondary overflow bin to cover an understock gap for the current run, you write the overflow bin ID in this margin section so the inventory team can adjust that bin’s count during their next cycle check. You sign and date all your notes so anyone reviewing the sheet later knows who completed the count, and you don’t need formal approval for discrepancies smaller than 10 units unless the production lead flags the order as high priority. If the discrepancy is larger than 10 units, you flag down the production lead before you pull any parts for the current run, to confirm if they want to adjust the run size or pull from a backup stock location.

When you pull this sheet for your next scheduled stock pull

The next time you grab this sheet to complete a count for a new production run, you first cross-reference the notes you added today to confirm any adjusted bin counts have been updated by the inventory team. You do not assume the listed bin quantity is accurate, even if no new discrepancies have been logged since your last check, because interim pulls for rush orders often aren’t logged immediately. You run through the same full count process every time you use this sheet, no matter how small the order quantity is, to catch any miscounts before they cause production delays. If the inventory team has resolved the discrepancy you logged today, you cross out the old discrepancy code and note the corrected count at the top of the sheet before you start your current count. Once you finish your check, you file the sheet in the hanging folder by the kitting station, so it’s easy to locate for the next team member who needs to complete a count for the same part number. You only discard the sheet when the part number is discontinued and all remaining stock has been pulled or scrapped, per the standard inventory retirement process.

About · Contact · Privacy · Disclaimer · Advertising · Terms