Lot Number on the Cert vs the Lot on the Traveler

Both papers have a lot. They are not the same string. You set the material test report flat next to the printed traveler on the bench edge, thumb pressing the corners to keep both from curling under the shop vent draft. You cross out the quick mental match you made 10 seconds earlier, leaning in to read each alphanumeric character one by one to confirm the mismatch isn’t just a smudge from grease on your work glove. You have no open non-conformance tags on hand right now, so you flag the corner of both documents with a piece of blue tape before moving further.

Cross-reference protocol for mismatched lot identifiers

You start by verifying you pulled the correct cert for the material you have staged, not a leftover cert from a prior run of the same alloy. Match the heat number first, as that value is consistent across the mill cert and the traveler’s material sourcing field, even if the lot numbers are assigned at different points in the supply chain. The lot number on the cert comes directly from the mill’s production run, while the lot number on the traveler is assigned by your inventory team when the stock is logged into your warehouse, so mismatches are not inherently a red flag, but they do require explicit documentation to link the two values for audit trails. You can cross-check the inventory log linked at the Traveler Desk if you need to confirm the inventory lot assignment for the heat number you have on hand.

Lot Number on the Cert vs the Lot on the Traveler
The vise is empty.

Traceability path for the stock pulled for this run

Follow the engraved heat number stamp on the end of the bar stock first, to confirm it matches the heat number printed on both the cert and the traveler. If the stamp is partially worn, use a wire brush to clear surface oxidation from the bar end until you can read every character clearly, taking a photo with your shop tablet to attach to the documentation if needed. You will also note the bin location the stock was pulled from, as inventory teams tag each bin with both the mill lot number and the internal lot number used on the traveler, so you can confirm the two values are linked to the same material batch before moving forward. If the bin tag does not list both numbers, you can pull the digital inventory record for that bin location to cross-reference the linked values.

Required documentation to attach before submitting for review

You will need three items attached to both the cert and the traveler when you submit them for quality review. First, the photo of the bar stock’s engraved heat number, clearly showing all characters so the quality team does not need to re-inspect the physical stock to confirm your match. Second, a printout of the inventory log entry for that heat number, showing both the mill lot number and the internal traveler lot number side by side. Third, a handwritten note on the margin of the cert linking the two lot numbers, dated and signed with your initials. You do not need to request a new cert from the supplier for this mismatch, as long as you can prove the two lot numbers refer to the same material batch. You will staple all documents together in the top left corner so they stay aligned through all subsequent job stages.

Discrepancy resolution steps to complete before cutting stock

Complete these steps in order, and do not begin any machining work until you have finished all four:

  1. Wipe all surface grime from both the cert and the traveler’s lot number fields to rule out a reading error caused by ink smudges or shop debris, then write both lot numbers side by side on a scrap of paper to confirm the mismatch is not a result of transposing characters as you read.
  2. Locate the physical stock pulled for this job and confirm the heat number on the stock matches the heat number listed on both documents, taking a clear photo of the stamped heat number for your records.
  3. Pull the inventory log for that heat number to confirm the mill lot number on the cert is linked to the internal lot number on the traveler, marking the relevant line on the log with your initials and the job number.
  4. Attach a printed copy of the relevant inventory log line to both the cert and the traveler, using a staple in the top left corner so it stays attached through all subsequent job stages.

Illustrative example: If the cert lists lot number ML-78249-2024 and the traveler lists lot number INT-4129, the inventory log will show both values linked to heat number H-92756 for 6061-T6 aluminum bar stock, confirming the mismatch is just a difference in numbering conventions between the mill and your internal system.

Sign-off fields to mark once you confirm lot alignment

Once you have confirmed the two lot numbers are linked to the same material batch, you will fill in three fields on the traveler’s material verification section. First, write the mill lot number from the cert in the blank “supplier lot number” field, making sure your handwriting is clear enough for auditors to read every character. Second, check the box marked “lot mismatch documented” to signal you have completed the required cross-check steps. Third, sign and date the field, using the same initials you used on the inventory log and the cert margin. You do not need to adjust the existing internal lot number printed on the traveler, as that number is used for internal tracking through the rest of the machining and shipping process. Double-check that all attachments are secure before you set the documents aside for quality review, as loose attachments will get separated from the job and cause delays when the quality team does their audit. You can move on to prepping your tooling while you wait for quality sign-off, as long as you do not make any cuts to the staged stock until you get formal approval.

When you pull this document for a follow-up run of the same part

You will first reference the margin note you added to the cert and the traveler for this initial run, to confirm you are using stock from the same linked lot number batch if you are pulling from the same bin. You will not need to repeat the full cross-reference process if you are using stock from the same bin, as the link between the mill lot and internal lot is already documented for that heat number. If you pull stock from a different bin, you will repeat the cross-check steps outlined earlier to confirm the lot number on the new cert matches the lot linked in the inventory log for the part number you are running. You will also add a new note to the traveler if you use a different lot batch, so all lot numbers used for the full order are documented in one place for future reference. Make sure you keep all attachments from the initial run with the document, so the full traceability trail is accessible for any future audits or customer requests for material documentation. If the part is being run for a repeat order a year or more after the initial run, you will still reference this document to confirm what lot batches were used for the first order, so you can match material specifications as closely as possible for the new run.

About · Contact · Privacy · Disclaimer · Advertising · Terms