The print date is at the bottom. The job started earlier. You can feel the faint raised texture of fresh laser toner along the edge of the date stamp if you run your thumb over it. No handwritten scribbles overlap that line yet, so you know no one has logged post-print work on this run before you.
Core Details Marked On This Print
This sheet pulls all logged pre-print job data from the shop work queue, so you don’t have to cross-reference three separate digital tabs to confirm run parameters. The print date itself is not the official job start date, which is listed in the top left corner under the job number, but it is the official cutoff for any last-minute engineering change orders that take effect for the parts you run today. The job start date listed in the top left refers to the date the customer submitted the final order and paid the deposit, which can be anywhere from 3 days to 6 weeks before the print date, depending on material backorder times and shop queue capacity. The print date only corresponds to the day the job moves from the scheduled queue to an active work bench, so it is the most relevant date for your work on the run today. Illustrative example: If an ECO was submitted 42 minutes before this sheet printed, it is included in the specs listed; any ECO submitted after the print timestamp does not apply to your current run, and you can flag those for the next shift if they appear in your digital notifications. You will also see the total required part count, allowed scrap rate for the material grade, and required in-process check intervals listed directly below the job number, all locked as of the print date. No updates to these numbers get applied to this physical sheet, even if digital queue values shift after you pick it up from the Traveler Desk. Any notes written on the sheet before you picked it up are from the scheduling team, who noted the allocated bench number and shift for the run, so you can confirm you are the correct person to be working from this copy. If you find a sheet with a print date more than 3 days old assigned to your bench, you alert the scheduling lead before starting work, as the specs may have shifted in the time between printing and allocation, and a newer copy may be available.

Direct Comparison Against Your Live Part Run
You only make one required cross-check with this sheet before you start machining, to confirm no misalignment between the printed specs and the stock you have loaded at your bench. This check takes less than two minutes, and prevents rework that can add hours to your shift if caught after the first 10 parts are cut. Follow these steps in order to complete the comparison accurately:
- First, match the material alloy code printed on the top right of the sheet to the stamp on the end of your loaded stock bar; if the codes differ, set the sheet aside and notify your shift lead before making any cuts.
- Second, cross-check the print date listed at the bottom to the timestamp on the most recent ECO posted for this job number in the shop portal; if the ECO timestamp is earlier, you confirm all ECO requirements are already listed on the sheet.
- Third, count the number of pre-cut blanks you have staged for this run and confirm the number is at or above the total required part count listed on the sheet, accounting for the allowed scrap rate.
- Fourth, sign and date the line directly above the printed date at the bottom of the sheet to confirm you completed this comparison, before you run the first test part.
If any of these checks fail, you do not discard the sheet, even if you receive a digitally updated version mid-shift. You keep this original printed copy attached to the first rejected part from the mismatched run, so the engineering team can trace exactly where the spec misalignment originated. You also never alter the printed date at the bottom of the sheet, even if you end up running the job across two separate shifts, as that date remains the official ECO cutoff for all parts run from this copy of the traveler. If you hand off the partially completed run and this sheet to the next shift, you add a short note of your progress on the back of the sheet, away from the printed core specs, so the next operator can pick up where you left off without obscuring critical data.
Filed Storage For Your Next Reference To This Job
When you finish your full run of parts, you tuck this sheet into the front of the job folder that travels with the finished parts to the deburr and inspection station, and it stays with that folder until the entire job is closed out. The next time you pull this same sheet out of the folder, you will be reviewing run data to resolve any questions about part tolerance deviations that turn up during final inspection, or to build baseline timing estimates for a repeat run of the same job in the future. You will not write any additional notes on the front of this sheet after you complete your initial comparison and sign off, unless you are noting a scrap event that occurs during your run that cuts your total usable part count below 80% of the required total. All other post-run notes get added to separate paper inserts in the job folder, so the original printed specs and print date remain fully visible and unobscured for future reference. If you are the one who pulls this sheet for a repeat job next quarter, you will cross-reference the print date from this run to the new print date for the repeat run, to identify any ECOs that were implemented between the two job runs before you start cutting parts. You can also use the print date to pull matching machine performance logs from the shop server, if you want to identify small adjustments you can make to speed up the repeat run without sacrificing part tolerance. Once the job is fully closed out and no repeat runs are scheduled for the next 12 months, the folder with this sheet inside gets stored in the locked back filing cabinet, organized by job number and print date, so you can pull it quickly if a new order for the same part comes in. You never remove this sheet from the job folder for any reason, even if you need to make a copy for your own personal run reference, as misplacing the original can lead to conflicting specs being used for future runs of the same part. If you are asked to share the specs used for this run during a customer review, you bring the full job folder with this original sheet included, so the printed date and locked specs can confirm exactly what parameters were used for every part you cut during your shift. You can also reference this sheet when you train new operators on how to align print dates to ECO timestamps, as the clear, unaltered date stamp acts as a reliable reference point for explaining the cutoff rule to new team members.
