A First Piece Tag You Have Not Tied On

A tag is on the bench. It is not tied to the part. You just finished running the third pass on the 6061 aluminum bracket, the cutting fluid still beading on its milled edges, and you reach for the zip ties you keep in the upper left bin of your tool chest to secure the tag before you move the part to inspection. A half-drunk bottle of water sits next to the digital calipers you used to take your first set of measurements, and the hum of the CNC mill you just paused fades into the background noise of the shop floor. You haven’t filled out any fields on the tag yet, save for the job number you scrawled in the top right corner as soon as the machine kicked off the first part of the 120-unit run.

Pre-printed Details Listed On This Tag

All core data for this job is already printed on the tag, so you only need to fill in measured values, signatures, and short notes as you work. The pre-printed material line lists 6061-T6 aluminum, which matches the bar stock you loaded into the mill this morning, so you don’t have to worry about mixing up material specs for this run. The part number printed on the tag matches the part number on the work order you pulled from your job queue at the start of your shift, so you know you didn’t grab a tag for a different bracket variant that has a tighter bore tolerance and a different surface finish requirement. The pre-printed inspection fields include space for the bore diameter, flange length, surface finish rating, and hole center spacing, all of which are the critical dimensions that impact how the bracket fits into the final assembly, so you don’t waste time measuring non-critical features that don’t affect functionality. There’s also a blank notes field where you can jot down any small adjustments you made to the mill’s offset when running this first part, so the inspector knows if you compensated for minor tool wear that showed up after the first 10 minutes of milling. A small perforated stub at the bottom of the tag has a matching serial number to the main body, so you can keep a record of the first piece check for your own logs once the inspection is complete.

A First Piece Tag You Have Not Tied On
The bin is shut.

Single Part-to-spec Comparison You Run Now

This side-by-side check confirms the first part out of the run meets all critical dimensions listed on the tag, so you don’t run 119 more parts that fall outside tolerance. You only use tools marked with the current month’s calibration sticker for these measurements, to avoid skewed readings that lead to unnecessary rework or scrapped parts. Follow these steps in order to complete the comparison before you tie the tag to the part:

  1. Wipe all cutting fluid and metal shavings off the bracket with a lint-free shop cloth, paying extra attention to the bore, the countersunk screw holes, and the outer edge that interfaces with the assembly housing, to get accurate, unobstructed measurements.
  2. Use the 0-25 mm micrometer to measure the bore diameter at three separate points along its depth, recording the lowest and highest reading in the corresponding fields on the tag, then average the three readings to get your final measured value. Illustrative example: The required bore diameter has a nominal value of 12.7 mm, with a +/- 0.02 mm tolerance range for this run, so any reading between 12.68 mm and 12.72 mm falls within acceptable limits.
  3. Use the digital calipers to measure the length of the bracket’s mounting flange, taking two measurements at opposite ends of the flange to confirm it is consistent across the full width, then record that measurement in the flange dimension field on the tag.
  4. Inspect the surface finish of the milled face against the reference sample taped to the side of your tool chest, checking for any chatter marks, deep scratches, or uneven milling that would make the part unsuitable for assembly, then mark the surface finish pass/fail box on the tag accordingly.

If any of your measurements fall outside the listed tolerance range, you don’t fill out the signature field or tie the tag to the part. Instead, you adjust the mill’s offset by the difference between your measured value and the nominal value, run a new first part, and repeat the comparison steps for the new part until all measured values fall within the allowed tolerance range. You never fudge measurements to get a first piece to pass, since that leads to hundreds of scrapped parts later in the run and delays the assembly team’s schedule by days or even weeks if the bad parts make it all the way to the assembly line. Once all measurements pass, you sign and date the machinist field on the tag, confirming you took all readings accurately, then use a zip tie to fasten the tag to the bracket’s unused mounting hole so it stays attached through inspection and inventory storage.

When You Retrieve This Tag Post-inspection

You leave the tagged part in the inspection holding bin by the quality lab door after you finish your initial check, and you will access this tag again once the inspector completes their full review, usually within 24 hours of dropoff. You can pick up the completed tag from the Traveler Desk outside the quality lab entrance, where inspectors leave all signed-off first piece tags sorted by job number for easy retrieval. When you pick it up, you first check the pass/fail box: if it’s marked pass, you tear off the perforated stub for your records, then you can restart the mill to run the remaining 119 units in the run, making sure to reference the tag’s noted dimensions if you need to make any small adjustments to the mill’s offset as the cutting tool wears down over the run. If it’s marked fail, you read the inspector’s notes in the comments field to see which dimension fell outside tolerance, make the necessary adjustments to your tool path or mill offset, run a new first part, and fill out a new tag for that updated first piece.

If the inspector marked it as a conditional pass, you follow the notes in the comments field to adjust your tool path slightly for the rest of the run to bring the dimension closer to the nominal value, even though the first part was still within acceptable tolerance. This small adjustment helps reduce the chance of later parts drifting out of tolerance as your cutting tool wears down over the course of the 120-unit run. You don’t leave the tag sitting on your bench for more than a few hours after you retrieve it, since you need to turn the main body of the tag in to the production scheduler once the full run is complete, so they can log the run as finished and update the job tracking system. The perforated stub you keep has a matching serial number to the main tag, so if there’s ever a question about the run’s first piece check, you can pull your stub to confirm your initial measurements match the inspector’s logged values. You also write the date and run size on the back of the stub before you tape it to your tool chest lid next to your other passed first piece stubs, so you can track your accuracy over time and spot any patterns in measurement drift that might indicate your calipers or micrometer need recalibration. You don’t discard the full tag even after the run is complete, since it stays filed with the job records for 12 months in case any questions about the run’s specifications come up later from the assembly team.

About · Contact · Privacy · Disclaimer · Advertising · Terms